Rig Setup and Control. - Serial port and level converter support

Welcome Guest! To enable all features please Login or Register.

Notification

Error

LOGic Forum » Hardware Support » Serial port and level converter support » Rig Setup and Control.

Rig Setup and Control.

Options View

Previous Topic Next Topic

N6ELO		#1 Posted : Wednesday, February 15, 2023 6:51:40 PM(UTC)
Rank: Newbie Groups: Registered Posts: 3 Location: Pulaski, Tennessee		I purchased a newer computer for my shack. It is running Windows 10 Home version. I have a Kenwood TS-950S and a Yaesu FT-857D connected via two seperate data cables from rigs to computer USB ports. I cannot get either one of them to connect to Logic 8. I may need some instruction to get this ironed out. Anyone familiar with setup of these rigs to Logic 8 and would like to assist, please contact me. n6elo@citlink.net 916-769-1536 Jon Pulaski, TN
Back to top		\| Edit by user

User Profile View All Posts by User View Thanks
Sponsor
Note: We receive a commission from Amazon when you purchase via this link. It does not affect your cost. Thank you!
Back to top

wa4pgm		#2 Posted : Thursday, February 16, 2023 8:06:43 AM(UTC)
Rank: Advanced Member Groups: Administrators, Registered, Beta Testers Posts: 360 Location: Farmville, VA Thanks: 34 times Was thanked: 221 time(s) in 191 post(s)		Go to the Radio Interface in LOGic and select the Radio driver, the correct COM port, Baud rate, etc... The COM port will probably not be the same as your old computer. 73 Kyle
Back to top
1 user thanked wa4pgm for this useful post.		WN4AZY on 2/16/2023(UTC)
User Profile View All Posts by User View Thanks

WN4AZY		#3 Posted : Thursday, February 16, 2023 10:35:06 AM(UTC)
Rank: Administration Groups: Administrators, Beta Testers Posts: 3,061 Location: Auburn, GA Thanks: 974 times Was thanked: 485 time(s) in 400 post(s)		Hi-- This might help: http://hosenose.com/Foru...ce-troubleshooting.aspx Like Kyle says, it is basically of getting the correct COM port, baud rate, etc/ What is the first error message you get? Tnx & 73, Dennis WN4AZY
Back to top		WWW

User Profile View All Posts by User View Thanks

N6ELO		#4 Posted : Friday, February 17, 2023 10:06:06 AM(UTC)
Rank: Newbie Groups: Registered Posts: 3 Location: Pulaski, Tennessee		Kyle, Thanks, but I have tried it all with different settings being sure the computer matches the Logic parameters. Dennis, I'm getting the error message of Timeout.
Back to top

User Profile View All Posts by User View Thanks

wa4pgm		#5 Posted : Friday, February 17, 2023 12:42:40 PM(UTC)
Rank: Advanced Member Groups: Administrators, Registered, Beta Testers Posts: 360 Location: Farmville, VA Thanks: 34 times Was thanked: 221 time(s) in 191 post(s)		The timeout error is most likely due to no communications to the radio. If the communications parameters match. Make sure you enabled the radio in LOGic? Has this worked before? Try another cable?
Back to top
1 user thanked wa4pgm for this useful post.		WN4AZY on 2/20/2023(UTC)
User Profile View All Posts by User View Thanks

N6ELO		#6 Posted : Friday, February 17, 2023 3:13:36 PM(UTC)
Rank: Newbie Groups: Registered Posts: 3 Location: Pulaski, Tennessee		Yeah...I ordered a new cable. It is a cheapeee and one of the ones that are not dependable.
Back to top

User Profile View All Posts by User View Thanks

Users browsing this topic
Guest

LOGic Forum » Hardware Support » Serial port and level converter support » Rig Setup and Control.

Forum Jump

You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.